![]() Главная страница Случайная страница КАТЕГОРИИ: АвтомобилиАстрономияБиологияГеографияДом и садДругие языкиДругоеИнформатикаИсторияКультураЛитератураЛогикаМатематикаМедицинаМеталлургияМеханикаОбразованиеОхрана трудаПедагогикаПолитикаПравоПсихологияРелигияРиторикаСоциологияСпортСтроительствоТехнологияТуризмФизикаФилософияФинансыХимияЧерчениеЭкологияЭкономикаЭлектроника |
Хід виконання роботи
Завантажити файл креслення vprava.dwg. Зберегти креслення під новим ім’ям у власній папці. Побудувати креслення за наведеним нижче протоколом. ******* Активація шару "Osi" ************************** Command: LINE Specify first point: 50,175 Specify next point or [Undo]: @305,0 Command: POINT3 Current point modes: PDMODE=0 PDSIZE=0.0000 Specify a point: END of Command: POINT Current point modes: PDMODE=0 PDSIZE=0.0000 Specify a point: @80,0 Command: LINE Specify first point: @0,80 Specify next point or [Undo]: @0,-160 Specify next point or [Undo]: Command: POINT8 Current point modes: PDMODE=0 PDSIZE=0.0000 Specify a point: end of Command: POINT Current point modes: PDMODE=0 PDSIZE=0.0000 Specify a point: @-45,0 Command: LINE Specify first point: @0,45 Specify next point or [Undo]: @0,-90 Specify next point or [Undo]: ******* Активація шару "Kontur" ********** Command: CIRCLE Specify center point for circle or [3P/2P/Ttr (tan tan radius)]: INT of Specify radius of circle or [Diameter]: 75 Command: CIRCLE Specify center point for circle or [3P/2P/Ttr (tan tan radius)]: INT of Specify radius of circle or [Diameter] <75.0000>: d Specify diameter of circle <150.0000>: 80 Command: LINE Specify first point: TAN to Specify next point or [Undo]: TAN to Specify next point or [Undo]: Command: LINE Specify first point: TAN to Specify next point or [Undo]: TAN to Specify next point or [Undo]: Command: TRIM Current settings: Projection=UCS, Edge=None Select cutting edges... Select objects: 1 found Select objects: 1 found, 2 total Select objects: Select object to trim or shift-select to extend or [Project/Edge/Undo]: Select object to trim or shift-select to extend or [Project/Edge/Undo]: Select object to trim or shift-select to extend or [Project/Edge/Undo]: Command: CIRCLE Specify center point for circle or [3P/2P/Ttr (tan tan radius)]: cen of Specify radius of circle or [Diameter] <40.0000>: d Specify diameter of circle <80.0000>: 40 Command: POINT 4 Current point modes: PDMODE=0 PDSIZE=0.0000 Specify a point: CEN of Command: LINE Specify first point: @0,50 Specify next point or [Undo]: @-50,-50 Specify next point or [Undo]: @50,-50 Specify next point or [Close/Undo]: @50,50 Specify next point or [Close/Undo]: @-50,50 Specify next point or [Close/Undo]: Command: LINE 9 Specify first point: INT of Specify next point or [Undo]: <Ortho on> Specify next point or [Undo]: Command: LINE Specify first point: INT of Specify next point or [Undo]: Specify next point or [Undo]: Command: TRIM Current settings: Projection=UCS, Edge=None Select cutting edges... Select objects: 1 found Select objects: 1 found, 2 total Select objects: Select object to trim or shift-select to extend or [Project/Edge/Undo]: Select object to trim or shift-select to extend or [Project/Edge/Undo]: Select object to trim or shift-select to extend or [Project/Edge/Undo]: Select object to trim or shift-select to extend or [Project/Edge/Undo]: *Cancel* Command: TRIM Current settings: Projection=UCS, Edge=None Select cutting edges... Select objects: 1 found Select objects: 1 found, 2 total Select objects: Select object to trim or shift-select to extend or [Project/Edge/Undo]: Select object to trim or shift-select to extend or [Project/Edge/Undo]: Select object to trim or shift-select to extend or [Project/Edge/Undo]: *Cancel* Command: PEDIT Select polyline or [Multiple]: Object selected is not a polyline Do you want to turn it into one? <Y> Y Enter an option [Close/Join/Width/Edit vertex/Fit/Spline/Decurve/Ltype gen/Undo]: j Select objects: 1 found Select objects: 1 found, 2 total Select objects: 1 found, 3 total Select objects: 3 segments added to polyline Enter an option [Open/Join/Width/Edit vertex/Fit/Spline/Decurve/Ltype gen/Undo]: W Specify new width for all segments: 0.8 Enter an option [Open/Join/Width/Edit vertex/Fit/Spline/Decurve/Ltype gen/Undo]: Command: PEDIT Select polyline or [Multiple]: Object selected is not a polyline Do you want to turn it into one? <Y> Y Enter an option [Close/Join/Width/Edit vertex/Fit/Spline/Decurve/Ltype gen/Undo]: J Select objects: 1 found Select objects: 1 found, 2 total Select objects: 1 found, 3 total Select objects: 1 found, 4 total Select objects: 1 found, 5 total Select objects: 1 found, 6 total Select objects: 6 segments added to polyline Enter an option [Open/Join/Width/Edit vertex/Fit/Spline/Decurve/Ltype gen/Undo]: W Specify new width for all segments: 0.8 Enter an option [Open/Join/Width/Edit vertex/Fit/Spline/Decurve/Ltype gen/Undo]: ******* Активація шару "Dim" ************* Command: DIM Dim: HOR Specify first extension line origin or <select object>: CEN of Specify second extension line origin: CEN of Specify dimension line location or [Mtext/Text/Angle]: Enter dimension text <180>: Dim: HOR Specify first extension line origin or <select object>: INT of Specify second extension line origin: INT of Specify dimension line location or [Mtext/Text/Angle]: Enter dimension text <295>: Dim: VER Specify first extension line origin or <select object>: INT of Specify second extension line origin: INT of Specify dimension line location or [Mtext/Text/Angle]: Enter dimension text <100>: Dim: DIAM Select arc or circle: Enter dimension text <150>: Specify dimension line location or [Mtext/Text/Angle]: Dim: DIAM Select arc or circle: Enter dimension text <40>: Specify dimension line location or [Mtext/Text/Angle]: Dim:DIAM Select arc or circle: Enter dimension text <80>: Specify dimension line location or [Mtext/Text/Angle]:
|